Brother HL-1000 Guia de preparacion

Laser Printer HL-800/1000 SeriesQuick Setup GuideRead this guidebook first to set up your printer andprepare your computer for the printer.Save all pa

8Action 5-2: Connect Your Printer to Your Computers using the USBinterface ( Only for HL-1050 with Windows 98 )The Universal Serial Bus is an interfa

9Insert the supplied CD-ROM into thedrive of your PC.Select “CD-ROM drive.”Click the Next buttonClick the Next button.The USB driver is installed.When

10TroubleshootingIf the printer does not print from the USB port, try reinstalling the USB driver as follows;1.Double-click the file ‘DeinsUSB.exe’ i

-11 -Action 6: Plug in and Turn on Your Printer1Plug the power cord into the AC poweroutlet and the printer power inlet.✒ NOTEThe shape of the power c

12Printing a Test Sample PageWe recommend that you print a test page. Refer to the instructions below.✒ NOTE The following test page operation will

13Action 7-1: Installation from CD-ROMThe supplied CD-ROM contains the following materials. Printer Driver & TrueType fonts -You need to c

-14 -Action 7-2: Prepare Windows 95/98 for the Printer from floppy disksYou need to configure Windows 95/98 for the printer by installing the printer

- 15 -Action 7-3: Prepare Windows 3.1 for the PrinterYou need to configure Windows 3.1 for the printer by installing the printer driver andTrueTypeTM-

- 16 -Action 7-4: Prepare DOS for the Printer (Only for HL-1040/1050 Users)How to Use the Printer in Your DOS Application Software(without using the W

- 17 -What Does Remote Printer Console Do?The Remote Printer Console (RPC) is a utility program which runs in the DOS environmentand comprises the fol

(For USA & CANADA Only)For technical and operational assistance, please call:In USA 1-800-276-7746 (outside California) / 949-859-9700 Ext. 329 (w

- 18 -Using the Remote Printer Console Main ProgramType C:\RPCX>RPCX and press theEnter key to start the Remote PrinterConsole main program.The Mai

-19 -Using the Printer Status Monitor ProgramType C:\RPCX>STMX and press the Enter key to make the Printer Status Monitor Programstay resident in y

- 20 -Action 7-5: Prepare Macintosh for the Printer (Only for HL-1040/1050 Users)You need to configure your computer for the printer by installing the

-21 -LAMPS AND SWITCHThis section refers to the following lamps and switch on the printer control panel.DrumAlarmReadyPaperDataToner✒NoteWhen the powe

- 22 -Drum LampThe Drum lamp indicates the drum unit is nearly at the end of its life.Lamp Printer statusOff ❍ The drum unit can be used.On ● The drum

- 23 -Other Control FeaturesSleep ModeWhen the printer does not receive data for a certain period of time (time-out), it enterssleep mode. Sleep mode

- 24 -REPLACING THE TONER CARTRIDGEThe printer can print approximately 2,400 pages (5% coverage: A4/Letter) with one tonercartridge. When the toner ca

-25 - High Temperature WarningAfter you have just used the printer,some internal parts of the printer areextremely hot. When you open the topcover of

-26 -5 Install the new toner cartridge into the righthand side of the drum unit. Make sure thatthe toner cartridge guide bar is exactlyaligned with th

- 27 -REPLACING THE DRUM UNITThe printer uses a drum unit to create the print images on paper. If the Drum lamp is on, itindicates the drum unit is ne

1Table of ContentsAction 1: Check the Supplied items --- 2Action 2: Place the Printer --- 3Action 3: Install the Toner Cartridge/Drum Unit --- 4Act

- 28 - High Temperature WarningAfter you have just used the printer,some internal parts of the printer areextremely hot. When you open the topcover of

-29 -4Install the toner cartridge into the new drumunit.Install the new drum unit into the printer.5Close the top cover.The printer automatically ejec

- 30 -ALARM INDICATIONS AT A GLANCEOperator CallsIf a recoverable error occurs, the printer indicates an ‘operator call’ by blinking the Alarmlamp and

-31-For errors shown below, the printer indicates an operator call by blinking the Alarm lamp. Ifyou use the printer with the supplied Windows driver,

- 32 -Error ActionSerial Interface InputBuffer Overflow (ForHL-1040/1050 Only)Press the panel switch to resume printing.Check the communication p

- 33 -Additional Memory (HL-1050 Only)The HL-820/1020/1040 printers have 2 Mbytes of standard memory and additional memorycannot be fitted.The HL-1050

34Installing the SIMMTo install the SIMM, follow these steps:1 Turn off the power switch and unplug the pcord from the AC outlet. Disconnect the intec

35PRINTER SPECIFICATIONSPrintingPrint Method Electrophotography by semiconductor laser beam scanningLaser Wavelength: 780 nm / Output: 5 mW max.Resol

36FunctionsTrueType Fontson disksTrueType-compatible soft-fonts for Windows on the supplied diskEmulation HL-820/1020:Brother Printing Solution for Wi

REGULATIONSFederal Communications Commission(FCC)Declaration of Conformity (For USA Only)Responsible Party : Brother International Corporation100 Some

- 2 -Action 1: Check the Supplied ItemsAfter taking the printer out of the carton and removing the packing materials, make sure thatthe following item

IMPORTANT - For Your SafetyTo ensure safe operation the three-pin electrical plug supplied mustbe inserted only into a standard three-pin power point

Shipment of the PrinterIf for any reason you must ship your Printer, carefully package thePrinter to avoid any damage during transit. It is recommende

-3-Action 2: Place the printerPlease take note of the following before using the printer.Power SupplyUse the printer within the specified power range.

- 4 -Action 3: Install the Toner Cartridge/Drum Unit1Unpack the drum unit assembly with thetoner cartridge included. Gently shake itfrom side to side

- 5 -Action 4: Load Paper into Your PrinterBefore loading paper, make sure that the paper meets the specification described in the On-line User’s Gui

- 6 -4Hold the tab of the right hand paper guideand press the catch to release the guidelock. Move the paper guide to fit the paperwidth.! CAUTIONFail

- 7 -Action 5-1: Connect Your Printer to Your Computers parallelinterfaceYou must connect the printer to your computer with a suitable interface cable